Epoxy powder coatings MT-100

Product details

Product description

MT-100 is a series epoxy based powder coatings that exhibit excellent corrosion protection and chemical resistance when applied over a properly prepared metal substrate. MT-100 is designed for interior application only. MT-100 powders are available in gloss, satin, matt and texture finishes in a wide range of colors.

Powder properties

	Typical value
Chemical Type	Epoxy
Density	1.2 – 1.9 g/cm³, depending on colour and effect
Recommended film thickness	60 – 90µm
Shelf life	12 months
Storage Conditions	Under dry, cool (≤ 25°C) conditions (open boxes must be resealed)
Curing schedule	15-20 min at 180°C 9-12 min at 190°C 5-7 min at 200°C

Pre-treatment

Aluminium components should receive a full multi-stage chromate conversion coating or suitable chrome-free pre-treatment or suitable pre-anodising to clean and condition the substrate. Detailed advice should be sought from the pre-treatment supplier. Iron phosphate and particularly Zinc phosphating of ferrous metals improves corrosion resistance. Aluminium substrates may require a chromate conversion coating.

Application

Powders can be applied by manual or automatic electrostatic spray equipment. Applicators and fabricators are advised to use a single batch for parts that will be assembled together. Differences are more likely with special effect powders. Bonded products have better application properties than blended products (more stable) but attention should still be paid to line settings in order to avoid “marble effect” and changes in aspect after recycling. Different substrates (aluminium, steel, galvanized steel…), use of primer, and big changes in film thickness may give a different aspect. Products with different codes should not be mixed even if same colour and gloss. It is recommended that for consistent application and appearance product be fluidized during application.

Application Method	Tribo, Electrostatic
Recycling	Unused powder can be reclaimed using suitable equipment and recycled through the coating system, but a minimum of 70% virgin powder should be used.

Test conditions

Actual product performance will depend upon the circumstances under which the product is used. The results are based on mechanical and chemical tests which (unless otherwise indicated) have been carried out under laboratory conditions and are given for guidance only.

Pre-treatment	Zinc Phosphate
Substrate	Polished steel
Curing schedule	5 min at 200°C (object temperature)
Film Thickness	60 – 70µm

Mechanical tests

	Typical value	Method/standard
Adhesion	Class 0	ISO 2409 (2 mm Crosshatch)
Erichsen cupping	Pass 5 mm	ISO 1520
Flexibility	Pass 5 mm	ISO 1519
Hardness	Pass – no penetration to substrate	ISO 1518-1 (2000g)
Impact resistance	Pass 2.5 Joules reverse & direct (20 in lb)	ISO 6272-2 (d/r)

Chemical and durability tests

Whilst maintaining the general protective and anti-corrosive properties of powder coatings, aluminum and copper/bronze metallic finishes, when submitted to the listed tests, may rapidly show a loss of metallic aspect. The results shown are based on tests which (unless otherwise indicated) have been carried out under laboratory conditions and are given for advice only, actual performance depends upon the circumstances under which the product is used.

	Typical value	Method/standard
Chemical Resistance	Excellent resistance to acid, alkalis, oils and chemicals at room temperatures.
Salt spray test	Pass, no corrosion creep more than 3 mm from scribe, 500 h	ISO 9227

Environmental and durability tests

	Typical value	Method/standard
Humidity	Pass – no blistering or loss of gloss, 1000 h	ISO 6270-2 CH (Constant humidity)
Exterior durability	Some chalking and loss of gloss after 3-6 months continuous outdoor exposure. Protective properties retained. Not recommended for outdoor applications.

Repair

Surface preparation	Damaged areas must be clean and free of grease or rust. Dry-sand the area with 600 grade paper down to the substrate. The area must be completely free of dust and cleaned with a non-aggressive solvent before proceeding. Any damage of the coating system must be repaired as soon as possible.
Application	For repairs a PU (2K or 1K) liquid paint is recommended.

PRODUCT

NEWS

Principle, Usage and Dosage of Fluorescent Whitening Agent 2025-09
How to make beeswax? 2025-09
Chinese Rhus Wax Usage and Production Process 2025-08
Emulsified wax classification and principle 2025-08
Thermoplastic acrylic resin 2025-08
LUBRITECH-300: High-Performance Lubricant Overview 2025-04
BIOPLAST-200: Biodegradable Plastic Overview 2025-04
POLYFIBER-900: Reinforcement Fiber Overview 2025-04
CLEANSOL-400: Industrial Cleaner Overview 2025-04
FLEXIPLAST-600: Flexible Plastic Overview 2025-04